![]() Recheck period for Solo/GetWork mining (default: 200 ms) Seconds to wait before reconnecting (default: 5) This setting is 30 minutes by default set to 0 to disable automatic switch back to primary pool. Switch back to primary pool after n minutes. Reconnect if no new ethash job is receved for n seconds (default: 600) Switch to next pool afer N failed connection attempts (default: 3) Submit stales to the dual mining pool: 1 - yes (default), 0 - no If you want to put all dual mining pools in dpools.txt, you need to set -dcoin blake2s in the command-line or in config.txt to force the miner to load the dual mining pools from dpools.txt -dstales Submit stales to the failover pool: 1 - yes (default), 0 - noĭual mining pool password (most pools don’t require it, use x as password if unsure)Ĭurrently only the Blake2s algorithm is supported for dual mining. Same as -pool but for the failover poolįailover ethash wallet (if missing -wal will be used for the failover pool too)įailover ethash password (if missing -pass will be used for the failover pool too)įailover ethash worker name (if missing -worker will be used for the failover pool too)įailover ethash stratum protocol (if missing -proto will be used for the failover pool too)įailover devfee Ethash coin (if missing -coin will be used for the failover pool too) Submit stales to ethash pool: 1 - yes (default), 0 - noįailover ethash pool address. ethermine, nanopool) - this is the default, works for most poolsĮthash coin to use for devfee to avoid switching DAGs: Selects the kind of stratum protocol for the ethash pool: Pool options -pool Įthash pool address (prepend the host name with ssl:// for SSL pool, or for solo mining).Įthash wallet (some pools require appending of user name and/or worker).Įthash password (most pools don’t require it, use x as password if unsure).Įthash worker name (most pools accept it as part of wallet). So you can use the same command line options as the ones you would have used with Claymore’s miner. Note that PhoenixMiner supports most of the command-line options of Claymore’s dual Ethereum miner PhoenixMiner in the command-line examples below. Under Linux you need to replace PhoenixMiner.exe with. You can download PhoenixMiner 6.2c from here: You can use this list as a reference for all Launch Parameters supported by PhoenixMiner. Hardware control options (you may specify these options per-GPU).I had to change the "Default Profile" the one on top. If I changed the power limit (or overclock settings) for example Phoenix Miner 5.5c for Ethereum profile, that will not work. Also running at 61C way cooler than 71C and that can prolong the card's life.īTW, I discovered that the only place to change power limit setting is by clicking on the GPU inside CudoMiner and clicking on the default settings and changing that. This will save almost 50% of electricity bill, for example, here in Chicago it is kinda expensive around 13 cents "total" per KWh. Which is around $5.5 to $6 a day according to website. But I lowered it to 52% to around 124 watts and still generates same "accepted hash rate" of 51.8MH/s. So I think the accepted hash rate of 51.8 is really good.īesides, to compensate, I was running the card at 100% full power consuming around 198 watts. Mine (pun unintended) shows has rates varying between 62.3MH/s down to 12MH/s depends on the difficulty of the calculation I guess. If you go to CudoMiner website and click on the computer's name that you are mining with, click on "Monitoring", you will see a graph for the hash rates. I have a stock RTX 3070, and I just started mining today, the "Accepted Hash Rate" for me is 51.8MH/s. Has anyone had this problem and can assist? I have deleted and reinstalled all soft ware including re-installing windows but the problem remains the same. I also have a situation where the GPU is stopping every 20min or so with a note that there has been no hash rate for 5min. My GPU is at 61Mhs and running for longer as I get more confidence but the revenue is up in the 12400 sats. I have tried to see on YouTube or the net in general as to what I am doing wrong but I cant find anything to assist in this regard. With some playing on the clocks it was getting up to 61Mhs on my GPU and revenue went up quite a bit to 12400 odd but now at the same settings I am only getting 900 - 3000 sat. I have a situation where I started off at default getting around 48Mhs, and the revenue was around 54300 sat. ![]() I am running a RTX3070 and I am also new to overclocking. I have just started mining and doing it now for around 2 weeks.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |